Accessories

The Button Blinky Safety Set provides a quick way to keep you visible on your next bike ride. Two high output LEDs give you steady and flashing modes with 160° of visibility. These little lights are brilliant, easy to mount and cute as a button! Button Blinky front specs: - 2 high output surface mounted LEDs provide steady and flashing modes - FL1 Tested - Run times: 12 hrs (steady – 15 lm) and up to 40 hrs (flashing - 15 lm) - Provides 160° of visibility - One CR2032 battery (included) - Mounts with rubber stretch strap - 18 grams Button Blinky rear specs: - 2 high output surface mounted LEDs provide steady and flashing modes - FL1 Tested - Run times: 20 hrs (steady – 4 lm) and up to 50 hrs (flashing - 4 lm) - Provide 160° of visibility - One CR2032 battery (included) - Mounts with rubber stretch strap - 18 grams

- Rugged 6061 aluminum construction is corrosion resistant - 100mm mudflaps provide ultimate coverage and are double-riveted for durability - Hardware is all stainless-steel and pre-installed for hassle-free mounting - V-stays for added stability - Disc brake compatible - 50mm width - Release Tabs on front fender for added safety - Meets EN test standards

Turn your bike into an all-weather vehicle with Planet Bike's Cascadia Fenders. Made of unbreakable Superflex polycarbonate with stainless-steel stays, they're ultra tough. They boast long mudflaps for the ultimate in splash and spray protection and the front fender has release tabs for easy on/off. Plus, the hardware is pre-installed for quick mounting.

The Hardcore Fender Hardware Kits are compatible with select Hardcore fenders, Full Fenders, Hardcore Recumbent Fenders, and SpeedEZ fenders. Includes: - Rear fender plastic clip - Fork and brake bridge-thru bolts - Stay bolts and lock washers Specific compatibility w/Planet Bike fenders: - 35mm Width: 700c x 35mm Fenders (Hardcore) - 45mm Width: 700c x 45mm (Hardcore, Full, and SpeedEZ); 700c Rear (Hardcore Recumbent) - 60mm Width: 26-inch x 60mm (Full, SpeedEZ, and Hardcore)

Compatible with: - Hardcore bike fenders - 700c x 45mm - Full bike fenders - 700c x 45mm - SpeedEZ bike fenders - 700c x 45mm - Hardcore Recumbent bike fender - 700c rear - Contains 45mm rear fender plastic clip, fork and brake bridge thru bolts, stay bolts and lock washers

Compatible with: - Full bike fenders - 26" x 60mm - SpeedEz bike fenders - 26" x 60mm - Hardcore bike fenders - 26" x 60mm - Contains 60mm rear fender plastic clip, fork and brake bridge thru bolts, stay bolts and lock washers

Deluxe steel floor pump – Metallic Grey Make sure you ride in comfort with the correct tire pressure. Planet Bike's redesigned STX floor pump has a big 3" integrated gauge and the Auto Head fits both Presta and Schrader valves. It’s engineered for smooth and efficient inflation. - Rugged steel barrel, plunger, and base - Anatomically designed handle for comfortable air compression - Auto Head fits both Presta and Schrader valves - Oversized 3 inch 160 psi dial gauge - Pressure rated to 200 psi - Needles included for pumping up sports balls - Large steel base for stability - Rebuildable - Height: 27”

Our Tenacious Oil is used for ultimate protection and durability for components that have movement with metal-to-metal contact. Our base oil has been produced for us by the same independent California refinery since 1971. The final blending of rust inhibitors and extreme wear additives happens at our facility before the product is bottled and shipped. - Ultimate protection and durability for metal-metal contact - Base oil with rust inhibitors and anti-wear additives

- Prevents rust, repels water - Extra heavy duty, nothing finer - Has achieved the Premium lubricant classification by all major bearing manufacturers worldwide

- Highly concentrated. Activate with water for incredible results or dilute for lighter degreasing tasks. - Engineered to fight its way to metal surfaces and stay there, then attack and break free the bonds holding oils, soils, and grime in place, and finally dissolve and contain to carry it all away. - Safe on any material, fully biodegradable, solvent-free, plant-derived, and zero-VOC. Degreaser 13 is a highly concentrated degreaser engineered for use with water to tackle tough degreasing tasks. Developed from scratch, specifically for the challenges of bicycle drivetrain degreasing, the advanced formula is engineered to fight its way to metal surfaces and stay there, then attack and break free the bonds holding oils, soils, and grime in place, and work together with water to dissolve and contain to carry it all away. Activate with water for incredible results on tough jobs or dilute for lighter degreasing tasks. Fully water soluble and further activated by scrubbing, agitation, and rinsing, the result is a spotless residue-free drivetrain. The advanced formula is also safe to use on any material, fully biodegradable, solvent-free, plant-derived, and zero-VOC.

These premium diagonal cutter pliers feature a compact 6" (150mm) length, forged and heat-treated steel construction, and ergonomic dual-density grips. The cutting jaws are self-opening and ready for years of service. - Compact 6" (150mm) length and self-opening jaw - Forged and heat-treated steel constuction - Ergonomic dual-density grips

- 110 gram, 8-function shop quality folding tool with 1.5, 2, 2.5, 3, 4, 5 and 6mm hex wrenches plus T25 torx wrench. - Super strong composite body features new design with improved comfort, better leverage, and stay-tight bolt design. - Professional-grade tool steel wrenches feature superior anti-corrosion finish for unmatched lasting performance. Pedro's folding wrench sets are essential for the shop, event, ride, and at home. These folding wrench sets feature professional grade tool steel for strength, superior anti-corrosion finish for unmatched lasting performance, and body made of lightweight but super tough composite material. The new body features improved ergonomics, shaped to perfectly fit in your hand, allow easy access to each tool, and with extra length for better leverage and control. In addition, the new stay-tight bolt design keeps tool bits from loosening over time. Backed by Pedro's lifetime warranty.

Pedro's folding hex set multi-tools are essential for the shop, event, ride, and at home. These folding hex wrench sets feature tools made from heat-treated tool steel for strength, superior anti-corrosion finish for unmatched long-lasting performance, and handles made of lightweight but super tough composite material. The handles feature an ergonomic shape to perfectly fit in your hand and allow easy access to each tool. In addition, the handle has a built in tool stop that allows the wrenches to be rotated 270 degrees for leverage and ease of use. The Folding Hex Wrench Set With T25 Torx weighs 115 grams and has 7 tools including 2.5, 3, 4, 5 and 6mm hex wrenches plus flat-blade and T25 torx.

- Backed by Pedro's Lifetime Warranty and Rust-Free Guarantee - Hex Wrenches: 2.5, 3, 4, 5, 6, 8mm - T25 and T30 torx - Flat blade screwdriver - 1-12 speed Chain Tool - 7 & 8mm Flare Box Wrenches - 3.23, 3.3, & 3.45 Spoke Wrenches - Shimano Crank Cap Tool - Presta Valve Core Tool - Micro Levers with integrated Quick Link Storage - 160 grams Pedro's new Rx Micro multi-tool is ready for trailside repairs and daily adjustments, delivering the perfect balance of size, weight, and function. It's designed for performance and durability with a 6061 aluminum body, premium CrMo tool steel bits, and an anti-corrosion finish backed by our Rust-Free Guarantee.

The tire lever, though seemingly one of the simplest and most basic of cycling tools, is one commonly used by almost every cyclist, and unfortunately, one often responsible for unnecessary frustration. Really, what is more fun than flatting far away from home, being thrilled you lugged that spare tube and pump, and then having your tire levers snap in two? Pedro's award-winning, universally loved tire levers feature molded box construction and a proprietary plastic composite blend that makes them the strongest levers available. The unique chisel tip shape easily inserts beneath the tire bead and the slightly thicker shape keeps the lever securely in place. Additionally, the bold shape of the lever and helpful dual spoke hooks makes removal of even the tightest tires a simple task. - Award-winning and universally loved - Molded box construction and proprietary plastic blend makes these the strongest levers available - Chisel tip shape is easy to insert beneath the bead and the slightly thicker shape keeps the tire lever from slipping - Bold shape makes it easy to remove the tightest of tires without bending or breaking

Having the right tool for the job is essential when working on modern bicycles. Pedro's Universal Crank Remover provides the tools required to properly remove press fit square taper and splined cranks. Unlike similar items offered by the competition, Pedro's includes everything you need in one convenient package The Universal Crank Remover fits all cranks using 22mmx1 threads and square, tapered bottom bracket spindles and splined Shimano Octalink and ISIS Drive bottom bracket spindles that do not use a “self extracting” system.

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-3 has 1.3mm tips on bent nose blades for medium, external snap rings.

• 15mm L-shaped hex wrench to fit Shimano rear thru-axle freehubs • Through-hardened industrial quality steel • Chamfered tips for a precision fit

Precision CNC machined aluminum tool for the installation and removal of 12-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8" drive. - 46mm 12-notch OD cup - Race Face® Cinch™, Rotor® BSA30, Zipp® Vuma™, Hawk Racing™ BB3086™, and more

Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut

There’s no easier or more effective way to patch a cut tire on the road or trail than carrying and using Park Emergency Tire Boots (3 per package). These thin, extra-tough patches peel and stick to the insides of tires to repair cuts and contain the tube until you can replace the tire.

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.

Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.

The HCW-16.3 is a combination 15mm pedal wrench and chain whip. Use for both pedal removal/installation and for cassette removal. Chain whip features improved compatibility with 5-speed to 12-speed mountain and road bike cassettes and freewheels. The HCW-16.3 is 10.75" long (27.3cm).

Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.

Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.

Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.

Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

• Park Tool Storage Hooks are perfect for hanging bikes, wheels, etc. • Vinyl coated to prevent scratching. • Wood threaded • Made from 7mm steel rod • For a pilot hole in wood, use a 1/4" or 6mm bit • Sold in pairs

• Updated to fit better in the hand with a more rounded, smoother shape • The precision sized SW-7.2 fits the three most popular spoke nipple sizes on the market • Nickel plated for years of service • Designed for the home mechanic. FIts the following size spoke nipples: • .127" (3.23mm) • .130" (3.30mm) • .136" (3.45mm)

The Fatty Object CO2 inflator fits on both Presta and Schrader valves and its oversized control knob is easy to operate, even with gloves on. - Precision machined alloy parts - For use with both Presta and Schrader valves

The Lucky Cat Cage is made from a single sheet of lightweight 5052 alloy. Cut in the shape of a Maneki-neko (Japanese for "beckoning cat"), this Portland Design Works bottle cage will undoubtedly bring good luck to its owner. Its side loading design makes it a great fit on small bike frames.

The PDW Outpost Mount allows you to attach a handlebar-mounted headlight to the side of your tapered wire basket—eliminating the problem of basket cargo blocking the light beam. The attachment plate compensates for the angle of a tapered wire basket, allowing the headlight to stay nice and level. - 32mm diameter clamping area for lights - Attaches with two M5 bolts and a steel backing plate - Mounts on left or right side

The Portland Design Works Owl Cage is made from a single sheet of lightweight 5052 alloy. Cut in the shape of a Great Horned Owl, its wings fold in to securely cradle your water bottle. Get an Owl and make your ride fly. - Constructed of 5052 alloy - Weight: 67 g (2.3 oz) - Includes two stainless bolts for installation - Lifetime PDWarranty

The Pathfinder USB Headlight from Portland Design Works is unlike any other bike light on the market, incorporating technologies to help you see and be seen while riding, day or night. The Vertical Cutoff Beam is designed to focus the 200 lumen main beam onto the road in front of you and prevents lost lumens that can blind oncoming traffic. For daytime riding, the Daytime Running Flash is bright enough to make you seen even on the brightest days. The Battery Meter lets you know exactly how much battery life you have left before needing to recharge with the included USB cord. The Pathfinder includes a powerful lithium-ion battery and a darkness destroying CREE LED bulb. It provides superior luminous guidance for up to 25 hours of ride time. The rugged construction is weatherproof and strong enough to handle the abuse of an urban commute. - 4 Modes: Steady low (4 hours), Steady high (2 hours), Pulse (8 hours), Daytime Flash (25 hours) - Lumens and burn times certified by Labsphere Illumia Light Measurement System to FL1 standard - Vertical Cutoff Beam to focus 200 lumens on the road ahead - CREE LED - Battery Meter for Li-ion battery - Micro USB charging cord included; 3 hour charging cycle - Weatherproof exterior for all season riding - One second delayed power switch to prevent accidental on/off - Light wakes up in last mode used - Includes UV-proof quick on/off handlebar mount - Weight: 57 g (2 oz)

This PDW light set consists of the Pathfinder 200 lumen USB-rechargeable headlight and the Io USB-rechargeable taillight. The Pathfinder 200 has a powerful lithium-ion battery and a darkness-destroying CREE LED bulb. The Io has 3 different modes, steady, flash, and pulse, and is perfect for urban riding. - Headlight: 4 Modes: Steady low (4 hours), Steady high (2 hours), Pulse (8 hours), Daytime Flash (25 hours) - Headlight: Vertical Cutoff Beam focuses beam into perfect bike path pattern while shielding the LED to prevent blinding oncoming traffic - Taillight: Mounts vertically or horizontally - Taillight: 3 modes (runtime) Steady (10h) Flash (20h) Pulse (20h)

Portland Design Works' Shiny Object is made from aluminum for strength and low weight so you won't think twice about bringing this ride essential along with you. A control knob keeps you in charge of the pressure, it takes threaded Co2 cartridges (sold separately) and it fits both Presta and Schrader valves. - Inflator only height: 44 mm (1.75") - Inflator only weight: 40 g (1.5 oz) 

Mount your tail light to the reflector tab on the back of a rear cargo rack with this Rack Bracket from Portland Design Works. - Compatible with all PDW rear lights except the Asteroid and Fenderbot - Horizontal holes are 50mm apart to fit European rack standards - Vertical holes are 18mm apart to fit most reflector mounts

The shape of the white VGD Cage was inspired by the legendary brandy toting St. Bernard rescue dogs of the Swiss Alps. The black VGD was designed to represent another type of rescue dog: the everyday Black Lab mix who's waiting to steal your heart and be adopted at the local shelter. - PDW donates 10% of profits from the Very Good Dog (VGD) Cage to animal advocacy organizations that help very good dogs in need.

You’ll love the way Osprey’s Raptor 10 carries when you’re riding rough, technical terrain thanks to the BioStretch harness and hipbelt that comfortably connect the pack to your body. Specially designed baffles in the 3.0 Liter LT liter Hydraulics reservoir reduce liquid movement for increased pack stability at high speed. The hydration sleeve is zippered for convenient refills and the hose routes over the right shoulder strap to the sternum strap where it anchors with a magnetic disk for on-the-fly access to the bite valve. The main compartment is accessible via a front zipper panel. There’s a stretch mesh front pocket for stashing a layer at the bottom of the big climb, zippered hipbelt pockets to keep a phone or other valuables secure, and a special scratch-free sunglass pocket to protect your shades. The LidLock helmet carry system gives you a place to secure your helmet when you’re off the bike. If you have mechanical troubles on the trail, a roll out tool pouch provides organized access for rapid trailside repairs. And if you ride late, there’s a blinker light attachment point and reflective patches for nighttime visibility. - Suspension: Atilon foam framesheet allows dynamic body movement while it spreads load across the entire back panel - Airscape Backpanel: Mesh covered ridged foam allows maximum ventilation while keeping the load close to the body - Biostretch Harness: Mesh covered die cut foam provides an active and contouring fit and ventilation. Soft, breathable spacer mesh contact surfaces. - Air Mesh Hipbelt: Air Mesh hipbelt for a breathable and ride stabilizing wrap - Front Stash Pocket - Front zippered stash pocket with heat embossed scratch-free lining safely holds sunglass or phones - Hipbelt Pockets - Dual zippered hipbelt pockets provide secure storage for often needed items - Hydration Compartment - Hydration sleeve with direct access zip offers fast loading. Hydraulics 3.0 Liter LT reservoir included - Stretch Mesh Front Pocket - Front stretch mesh pocket for quickly stashing extra gear

It's finally here—the perfect pack for the mountain biking minimalist. Ideal for quick laps on local singletrack or gravel trails, the Savu lumbar pack has two rigid pockets that make it easy to pull and replace water bottles as you pedal, so you can stay hydrated without stopping. Angled hipbelt and compression straps keep the pack close to your body and provide maximum stability over every type of trail. No creep-around here. Not a two water bottle kind of ride? No problem. Each water bottle sleeve can tuck away when not needed to provide a streamlined pack. Any way you customize it, the main compartment and side hipbelt pockets will fit vital flat-fixing tools, a tube, snacks, and other small mountain biking essentials. LUMBAR CARRY - For riders who require hydration, but prefer the off-the-back carry and minimalism provided by lumbar packs. RIDE STABILITY - Our bike-specific, angled hipbelt and compression straps provide stability and comfort by keeping the pack close to your body. BOTTLE CARRY - The perfect solution for stable lumbar carry allows you to access your bottles with ease. For short rides without water, the bottle pockets compress to maintain stability and keep the pack close to your body. Water bottles not included. FEATURES - AirScape backpanel with contouring lumbar wrap provides maximum stability - Dual snap-in-place or tuckaway water bottle sleeves - Easily accessible zippered main compartment with internal tool organization - Dual zippered hipbelt pockets - Blinker light attachment * Water bottles not included AIRSCAPE LUMBAR BACKPANEL - Extra thick ridged foam with center air channel for excellent ventilation HIPBELT - Airmesh wrap hipbelt with zippered fabric pockets provide stability and breathability - ErgoPull waist strap closure system allows for proper snug and stable fit

Heading out for a day hike where all you need is water to quench your thirst and room for a few essentials? Say hello to the Talon 6. Seen at not just the start, but more importantly the finishes of 50k trail races, mountain bikers, and on bird-watching trekkers alike, it's the perfect solution for keeping your urban or wild journey simple so that your focus remains on the important things. The experience itself. Body hugging BioStretch hipbelt keeps the load stable two included 570 ml BPA-free PackBottles ensure that the last thing you'll be is thirsty on the trail. Carry an extra layer with the external StraightJacket compression straps, fill your bottles and hit the trail, path and beyond. Features - Lumbar pack with Dual-zippered panel access to main compartment - Front panel zippered slash pocket - Padded bottle sleeves with bungee retention straps - Horizontal StraightJacket compression straps - Two 570 ml BPA-free PackBottles included - Bottle volume 570 ml - Bottle weight 2 oz/0.06 kg

Osprey’s women’s-specific Verve 9 is the ideal cycling companion. Made to carry weight in an upright position, a foam framesheet spreads the load across a ventilated mesh backpanel for all-day comfort. The BioStretch shoulder harness provides a contoured fit and the webbing hipbelt is removable to shave ounces. If you end up carrying extra weight, top compression straps lend extra load stability. Access your gear in the main compartment via the zippered front panel. You can slip small items into the harness pocket or stash a layer in the front fabric shove-it pocket for quick access. There’s even a scratch-free slash pocket for your shades. Bike-friendly features include a Hydraulics LT 2.5 liter reservoir with magnetic bite valve retention, internal bike pump storage loops, and Osprey’s innovative LidLock helmet attachment system. Suspension - Atilon foam framesheet allows dynamic body movement while it spreads load across the entire back panel Airscape Backpanel - Mesh covered ridged foam allows maximum ventilation while keeping the load close to the body Biostretch Harness - Mesh covered die cut foam provides an active and contouring fit and ventilation Webbing Hipbelt - Removable 20mm webbing ride stabilizing hipbelt Additional features: - Upper Side Compression Straps - Dual upper side compression straps help stabilize the load - Front Shove-It Pocket - Front panel shove-it pocket with zippered organization pocket helps gear accessible and systematized - LidLock Helmet Attachment - An elasticized LidLock helmet attachment system provides storage for your helmet - Blinker Light Attachment - The blinker light attachment strap found near the base of the front panel of the pack allows for quick light attachment for high visibility in the dark - Hydration Compartment - Hydration sleeve with direct access zip offers fast loading. Hydraulics 2.5L LT reservoir included - Harness Pocket - Stretch mesh harness pocket provides easy access to energy snacks and other quickly needed items - Stretch Mesh Side Pockets - Dual stretch mesh side pockets provide additional storage for essential items

Osprey’s Viper 9 is designed for cyclists who like to push the limits—packing full day rides into half that time and bringing just enough gear to make it home. Whatever you choose to carry, the foam framesheet spreads your load across a ventilated mesh backpanel for all-day comfort. The BioStretch shoulder harness provides a contoured fit and the webbing hipbelt is removable to shave ounces. If you end up carrying extra weight, top compression straps lend extra load stability. Access your gear in the main compartment via the zippered front panel. You can slip small items into the dual side mesh or harness pockets or stash a layer in the front fabric shove-it pocket for quick access. There’s even a scratch-free slash pocket for your shades. Bike-friendly features include a Hydraulics LT 2.5 liter reservoir with magnetic bite valve retention, internal bike pump storage loops, and Osprey’s innovative LidLock helmet attachment system. Suspension - Atilon foam framesheet allows dynamic body movement while it spreads load across the entire back panel Airscape Backpanel - Mesh covered ridged foam allows maximum ventilation while keeping the load close to the body Biostretch Harness - Mesh covered die cut foam provides an active and contouring fit and ventilation Webbing Hipbelt - Removable 20mm webbing ride stabilizing hipbelt Additional features: - Upper Side Compression Straps - Dual upper side compression straps help stabilize the load - Front Shove-It Pocket - Front panel shove-it pocket with zippered organization pocket helps gear accessible and systematized - LidLock Helmet Attachment - An elasticized LidLock helmet attachment system provides storage for your helmet - Blinker Light Attachment - The blinker light attachment strap found near the base of the front panel of the pack allows for quick light attachment for high visibility in the dark - Hydration Compartment - Hydration sleeve with direct access zip offers fast loading. Hydraulics 2.5L LT reservoir included - Harness Pocket - Stretch mesh harness pocket provides easy access to energy snacks and other quickly needed items - Front Stash Pocket - Front zippered stash pocket with heat embossed scratch-free lining safely holds sunglasses or phone

The Back-Roller City is an economical starter version with clear features and plenty of space for bike touring. With its symmetrical design and slanted shape on both sides, this classic Ortlieb bag provides enough space for pedaling, while also allowing individual use on either the left or right side of the bike. The patented Ortlieb QL1 system allows fast and easy single-handed mounting and removal of the panniers, and is suitable for racks with a tube diameter up to 16 mm (hook inserts for diameters of 8 and 11mm are included). -Sold as a pair

Weighing just 290 grams (including adapter), the fork pack offers approximately 4.1 liters of additional storage space for bike packing. With the help of the QLS adapter, this ultra-light bag with roll closure can be mounted on forks with eyelets or cage mounts intended for this purpose, as well as on forks without cage mounts, as long as the fork blades sport a constant diameter of 30mm to 42mm. Specifications: - Ultralight, waterproof bag (single pocket) with roll closure - The Fork-Pack is primarily designed for attachment to bicycle forks, but it can be mounted on non-tapered vertical tubes with a consistent diameter, e.g. Kick Style Scooters - Abrasion-resistant PU-coated nylon fabric - Allows additional luggage to be carried on bikes using the Quick-Lock S (QLS) adapter system - Adapter is compatible with forks with eyelets and tubes with constant diameter from 30 mm to 42 mm - The Quick-Lock S mounting bracket may be bolted directly to a fork with „braze-on“ eyelets or attached to vertical tubes using the supplied band-clamps - Ultra-fast installation, with one click the bag snaps in to place - The removal is just as fast, simply move the release lever and pull the bag upwards - The robust Quick-Lock S mounting plate remains mounted to the bicycle - Low profile locking elements ensure snag-free use - Internal stiffener - Reflective ORTLIEB logo - Maximum load 3kg / 6.6lbs

The ORTLIEB Toptube Frame-Pack is the smart solution for all who want to use their frame's main triangle for storage space without having to do without their water bottle. The solution also works for those who have full-suspension mountain bikes with limited triangle space. With its 4-liter payload, the Toptube Frame-Pack provides plenty of space for heavy equipment such as tent poles, tools, and food supplies, while also helping to secure a low center for improved rising performance. And given that the bag and its zipper are waterproof, you can even cross rivers on your bikepacking tour without worrying about your stuff getting wet. The Frame-Pack attaches easily to your top tube and seat tube with the help of sturdy and highly adhesive Velcro straps. FURTHER FEATURES: - Ideal for all bikes with limited triangle space - Reflecting logo ADVICE: Suitable for carbon fiber frame.

Minimalism to the max is a good description of the ultra-lightweight seat pack for road bikes and mountain bikes. The Micro Two was specially designed for those demanding tours when every gram counts. In addition to being 100% waterproof, the pack offers you space enough for a few critical items such as a replacement tube, a bike kit, or first aid materials. Its roll closure and elastic drawstrings allow you to collapse its size down to a minimum. And thanks to its extremely small dimensions, it can be mounted to your bike in an extremely space-saving manner. Simply attach the mounting bracket to your seat stays. Then attach or detach the pack with a single hand using the snap buckle. While the snap-on system was again enhanced for user-friendliness, the Micro Two remains compatible with all previous models. Further Features: - PVC-free, polyurethane-coated nylon fabric - No protruding plastic parts on the inside - Includes the mounting bracket - Simple attachment - Reflector

For all models, including the Back-Roller and Sport-Roller, with Stealth buckles Need to replace a pair of broken buckle? - 2 plastic buckles (male and female ends, 25 mm, black)

Get ready for your next bikepacking adventure! As a key item in your bikepacking setup, the ORTLIEB Seat-Pack comes with Velcro straps to enable convenient and secure mounting to your seat stem. Projecting backwards from the seat stem, your Seat-Pack also serves as a rear fender. The spacious, waterproof Seat-Pack keeps its contents (e.g. an extra set of clothes) safe and dry. Depending on how long you plan to be away and your Seat-Pack model, you can conveniently adjust the volume of your pack from 7 to 11 liters by adjusting the roll closures on the sides. An additional valve allows you to quickly and easily compress your soft gear for a more compact fit. Your Seat-Pack also serves as a replacement backpack when you're out on a day trip, no matter whether you ride a hybrid bike, a mountain bike, a road bike, or an electric mountain bike. The Seat-Pack is available in two sizes. This model needs only six centimeters of space on your seat stem. That's why the more compact model is ideal for smaller frame sizes, full-suspension bikes, and adjustable seat stems. FURTHER FEATURES: - Reinforced fabric at all points of contact to the seat - Vertical daisy chain for rear light - Also suitable for carbon seat stems - Lightweight design - Four 3M Scotchlite reflectors available for full extension

Get ready for your next bikepacking adventure! As a key item in your bikepacking setup, the ORTLIEB Seat-Pack comes with Velcro straps to enable convenient and secure mounting to your seat stem. Projecting backwards from the seat stem, your Seat-Pack also serves as a rear fender. The spacious, waterproof Seat-Pack keeps its contents (e.g. an extra set of clothes) safe and dry. Depending on how long you plan to be away and your Seat-Pack model, you can conveniently adjust the volume of your pack from 8 to 16.5 liters by adjusting the roll closures on the sides. An additional valve allows you to quickly and easily compress your soft gear for a more compact fit. Your Seat-Pack also serves as a replacement backpack when you’re out on a day trip, no matter whether you ride a hybrid bike, a mountain bike, a road bike, or an electric mountain bike. Thanks to its elastic drawstrings on the top, the 16.5-liter model offers additional space for items you need to be able to access quickly. This model needs only 15 centimeters of space on your seat stem. FURTHER FEATURES: - Reinforced fabric at all points of contact to the seat - Vertical daisy chain for rear light - Also suitable for carbon seat stems - Lightweight design - Four 3M Scotchlite reflectors available for full extension

Our first multi-tool includes all the key bits to assemble and disassemble your bike on-the-go. Includes a 15mm and 17mm swappable pedal wrench, 4, 5, 6 and 8mm hex wrenches and a 17mm socket with an integrated storage compartment. The Travel Tool is light and easy to carry, but big enough to allow you to actually tighten everything down properly. Features: - 4mm, 5mm, 6mm, and 8mm hex wrenches - 17mm deep socket - Integrated storage compartment - Pedal Wrench (15mm and 17mm spanners included) - 8-inch Full length arm for proper leverage

Whether you're heading to the beach, riding to the grocery store, or just cruisin' around, Nantucket's Cisco Handlebar Basket will get you and all your goodies there in style. This beautiful rattan basket boasts high-quality wicker construction and a rolled rim for extra durability, and it attaches to most bicycle handlebars with its easy-to-use straps and buckles. - Dimensions: 13" (L) x 10.75" (W) x 9.5" (H) - Maximum Weight Limit: 13 pounds

Perfect for heading to the park or riding to a friend's house, Nantucket's Kids' Cruiser Basket will get your child and all their goodies there in style. This beautiful wicker basket boasts high-quality rattan construction and a rolled rim for extra durability, and it attaches to most kids' bikes with its easy-to-use straps and buckles. - Dimensions: 10" (L) x 7.5" (W) x 7.5" (H) - Maximum Weight Limit: 8 pounds

Lightship baskets are made from finely woven rattan cane, the outer skin of the natural rattan vine. These baskets are replicas of the Nantucket Lightship baskets first produced in Nantucket during the whaling era of the 1800s. Attaches to front handlebars with two leather straps. - Dimensions: 12" (L) x 7.5" (W) x 9" (H) - Maximum Weight Limit: 13 pounds

Surfside Collection wire front baskets attach to the handlebars with an easy-to-use bracket (included), making them the perfect grab & go basket! - Dimensions: 13.25" (L) x 10" (W) x 9" (H) - Maximum Weight Limit: 15 pounds

- Lightest and most versatile MTB mudguard available - Uses hook and loop Velcro straps to attach to the bridge and lower legs - Compatible with forward and double bridge fork designs and all wheel sizes

- Fast and effective grease-cutting formula - Removes all chain oil and wax residue - Safely eliminates drive chain contaminants - Biodegradable - Ideal for use with chain cleaning devices - Trigger spray included for easy application on cassettes, chainrings and derailleurs - Safe for metal, plastic, rubber and seals

Muc-Off Waterless Wash is a highly advanced, easy to use spray which cleans and polishes in seconds without the need for water. It details your whole bike, motorcycle or car in seconds leaving behind a streak free shine. Its innovative formula is designed to encapsulate any surface dirt to prevent scratching. Use it to remove light contaminants in between major washes. - Cleans and polishes in one application - No need for water - No residual dust or streaks - Powder-free - Great for eBikes - no danger of getting electrical contacts wet